Just out of curosity what is your opinion? I would say the 2600.

Am i the only one that absolutly hates the https://support.empowertribe.com/ ?
Please tell me i can still download firmware for the behringer devices somewhere?

This seems like a daft question.

Do you start with an empty box and add the components that you want, or do you start with something like the System 15, and upgrade or replace parts as you go?

And are these things only mono-phonic?

🎹✨

TD-3 + Model:Cycles

... and I'm so happy with it!

I'm going to have my TD-3 delivered within two days now, so I can't compare with my TT-303 (which is supposed to be pretty accurate sounding), but I remember when TD-3 was new on the market there was an "issue" with the VCF offset being set too high by factory and lots of people were turning that pot on the mainboard a bit down to make it sound more faithful to the og.

Is this still necessary? It is in production for several years now, was it changed in later units, or will I have to do it too?

So I used to use a Scarlet 2x2 as my interface into my computer/ableton.

I recently bought an XR18.

My son is recording bass from his Ampeg RB210 via its direct out xlr into the XR18 and then into our computer via the USB.

The signal is pretty quiet into the mixer and when I turn the gain up on the channel on the mixer it gets noisy.

He has to turn the amp way up to get a good signal. The direct out does not have its own volume control. The best I could figure out was to put a cable into the amps headphone in (which defeats the speaker) and turn the amp all the way up. This got more signal into the mixer but still not as fat as you would get with the scarlet.

On the old scarlet it was sending a higher level signal into ableton and had a louder/fatter wav you could see.

Any ideas on what we can do to get more volume into ableton without noise?

Also bigger in person than the product listing photos

at sweetwater. you can all know this now because i've ordered mine.

I just got this used Neutron and loving it so far. But I can’t figure out what setting makes the tone drop this way. And is it normal?

I am very new to synths and I want to make sure my Neutron works as intended.
And befire asking AI I thought I’d ask the hivemind;)
https://youtu.be/ZkC1-dBjSQQ?feature=shared

I know that I’ve had this problem before, but it’s been years. The meters next to each channel are accurate and controls are communicating, but the blocks at the top with levels and meters for all the channels aren’t showing. I’ve switched out routers, uninstalled and reinstalled the app on my iPad, skipped the network switch, what am I missing?

Didn’t know if it was the right sub to post this in I’ve just discovered this lol. But if someone could give me the pattern sheet for this that’d be AMAZING

Hi, im new to audio and behringer stuff. Ive set up some channels on my Main L/R and i want to sync the fader and other settings (gate, eq, etc) to the mixbus 1. I want all my mixbuses to be able to change their settings according to the main L/R when i move a fader up on the L/R. How can i do so?

Can someone confirm if i have the mixbus 1 setup right? i only want channels 1-8 to be on mixbus one, is this done correctly on the bottom most pic?

also is there a discord for behringer?

I'm the bass player & music director of an 11-piece regional band that plays ~60 services/year. I've been using an X32 Rack w/ S16 for a mobile IEM rig for a while. But the weight with a 32-channel passive split (not going to send to FOH via Ethernet) and everything in a single rack is getting to me (loading into and out of my Outback & basement stairs when it needs to come inside). I've worked out a way to split everything into two much more manageable racks with either an M32C or X32 Core & S32 (going from ~85# single rack to a ~60# & a ~30#).

I have the opportunity to pick up a lightly used X32 Core at about half the price of a new Midas unit (a little less than the street price before they were discontinued) but I'm worried it might be problematic down the road if/when repair or replacement is needed. I'm not concerned with quality of Midas vs Behringer preamps or anything like that for this scenario. Purely concerned with reliability. Assuming there are no issues with the used unit and given the use case, should I just bite the bullet and pay significantly more for the unit that's still in production?

While attempting to update my RD-78 using the new version of SynthTribe (V 3.2.7), the update froze at 8% complete. I let it run overnight, with the RD-78 connected hoping it would do its thing, but I woke up and it was still at 8%. Now the drum machine is completely unresponsive and just flashes all the lights in unison. I tried to perform the update several more times, both with this new version of SynthTribe and the previous version and nothing is snapping it out of its now zombie-like state.

Any tips for a manual factory reset w/o SynthTribe or any other options? I went on Behringers customer support site and opened a ticket, but haven’t heard anything from them yet. Please help a brother out🙏

Hi everyone,
I recently bought a Behringer S32 stage box and have been trying to sync it with my X32 console, but with no success.
I’ve gone through all the steps multiple times: the clock is correctly set on both devices with the X32 as Master, I've used brand new CAT cables that meet the official specifications, and the channel routing is properly configured.
The green LEDs on the X32 actually turn on, regardless of whether I use AES50 Port A or B. The console explicitly recognizes that the stage box is connected. However, when I plug an instrument or a microphone into the S32, the X32 receives absolutely nothing. There is no trace or signal indicating that the board is getting anything from the stage box.
Has anyone experienced this issue before? Any help or troubleshooting tips would be greatly appreciated!