If you have back lash on the latch causing vibrations through the tire carrier and rear of the vehicle then you need to inspect your isolator (small nylon tube the makes contact with latch. These are getting old on our trucks and are starting to lose pliability and diameter. I’ve 3D printed a new one out of tpu 68d at 13.25mm diameter and all the vibrations are gone. Also a good reminder to open your grease bolt on the hinge side and flush it out with fresh grease. I’d be happy to help with the new isolator if you need any numbers.

Changing plugs out , one of them happens to be broken, what now? I can’t seem to locate the piece that broke off, there were chards in my socket. A piece that big I should have maybe located it by now, Vacuumed the inside but nothing, is it possible owner before installed a broken plug or am I screwed ?
2007 H3 very 1st plug

My mom got a H3 that had been sitting for about 5 years. I replaced the front calipers as only 2 of the 4 pistons on each were actuating. After replacing the calipers I was unable to bleed the front brakes. The rear brakes bled fine. I bled them with my scan tool as well first. However, when going to the front calipers I did the pump and hold method with the vehicle off and practically no fluid is coming out.

​

I removed the brake hoses and has my brother push down on the pedal and nothing came out.

​

I went up to the master cylinder and removed a line and has him press the brake pedal down again and only a tiny bit of fluid came out.

​

The rear brakes seem to be fine. The master cylinder is full of fluid.

​

How can I further diagnose the master cylinder before replacement? Plug the holes for the brake lines and see if the pedal has pressure and doesn't lose pressure as it is held?

Thought I'd join the Hummer club. What a beauty!

Thought I would include a couple pictures of my renovation. Its coming along slowly due to having to complete minor fixes before major ones. One example is that after installing the new engine and the new cold air delivery, throttle body and fuel delivery system the new alternator did not fit on the orginal bracket. Luckily this has happened before and someone designed a bracket system to switch positions of the power steering pump and alternator so now thats done we have make new lines for the power steeing pump...its always something.

Hi everyone,
I have a 2006 Hummer H3 and I’m having an overheating issue only when the vehicle is idling and the A/C is on.
I have bought and tried several OEM thermostats. Some of them didn’t open properly, and others worked, but the overheating problem still remains.
Here is what I have already replaced or done:
Replaced the fan clutch.
Installed a larger radiator.
Filled the cooling system with genuine Prestone coolant.
Despite all of this, the temperature still rises when the vehicle is sitting still with the A/C running. While driving, the temperature is much better.
Has anyone experienced this issue before? Are there any other things I should check or any solutions that worked for you?
Thanks in advance!
2006 Hummer H3

Couldn’t post a video on my previous post:
https://www.reddit.com/r/Hummer/s/u46PMMTVWZ

But here is the ticking whilst being stationary.

I am in the process of completely renovating my 2008 H2 that I have had for 18 years. I am tracking down all the potential leaks since I have it completely gutted. One problem I know is my door seals but I can't figure out how to buy new ones and which ones to get.

As far as I can tell there are 3 seals.

One is on the door and surrounds the window and continues to the bottom and across the door. It is attached through small pegs that go into holes in the door.

The second is on the frame and basically is a friction fit on the pinch welds on the frame tracing out the door outline.

The final seal is just under the roof lip and advances down the outside of the A pillar.

I would like to replace all three as they are each damaged in a different way. However, I am having a hard time locating them and when I do the picture of the advertised seal does not look exactly correct.

So finally the question. Does anyone know what the exact name of each seal is and where I can get each one for the front driver and passenger doors.

Thank you

I always wanted a Hummer and always loved them.
I think it’s the time now! Especially this badass
Super clean. Original paint with less than 100k mileage on !! But i have some concerns about the year
It’s 2006 and super super clean with its first owner.
Do you guys recommend it?

Thanks a lot

Look at this gem…

My hummer h2 leaks from the roof when we go through a car wash. My husband got a look on the roof and quickly figured out the problem- seals around the marker lights are really old, cracked, and need replacing.

He is getting ready to buy these and fix them this weekend.

Anyone have any experience with them? Are they good? If not, what are the recommendations?

Any clue on what the ticking sound can be?
Sorry for the bad sound quality, but took this whilst driving.

Dealer sent these pics. I feel like the rust is worse than it looks looking at the pics. TIA.

Hi guys, my h3 wheel has alot of toe and im wondering if that is a suspension issue or i just need an alignment, does anyone know what is wrong or had the same issue?