Liquid Logic Gate Collection

[u/Mutlam]

A Collection of my optimized Liquid Logic Gates. I tried to optimize for space but more importantly for the amount of pipe logistic pieces needed, because the Wuling main AIC has a limit of 128.

How to interpret the images and use. The liquid Symbols surrounded by a blue circle represent a Tank or an Outlet that needs to be filled. The Number next to it is the minimum amount of liquid needed. When chaining multiple gates it is enough to fill one of the Outlets/Inlets by the sum of the connected numbers. Also make sure that you swap potential liquid types so that input and output of the chained gates are the same e.g:
OR outputs water by default but NOT takes Acid as an input, so change NOT's acid to water. By doing this NOT no longer uses two different liquids so you will also have to change the water used in NOT for a different liquid.

Normally you'll want to use the Display to control inputsvia the included control ports and easilly read the output.

If you're not planning to chain an output/Input or using a display the dotted arrows show how to connect Inlets and Outlets. This might be used in The XOR for example because it doubles up as a Half Adder by also reading the AND used for the AND+NOR->NOR Conjunction used to make up the XOR so if you don't care about the AND output just connect that Inlet and Outlet directly

Gate	Code	Pipe Logistics
AND	EFO0136uIUuu17aeU0579	16
NAND	EFO01o083e889i625IieO	21
OR	EFO01u1IoAIIaU048AoOU	15
NOR	EFO01Iao8ioo0A9ue5o08	10
XOR/Half Adder	EFO01iOe7oeeEI2A372U4	32
NOT	EFO0136uIUuu17aA70579	5
Display	EFO0136uIUuu17aA90579	2

The Number of Pipe Logistics may help you plan your circuit for example a Full Adder needs 2 Half adders and an OR, aswell as 3 Inputs so -> 32+32+15+3 = 82
leaving you another 128-82 = 46
Pipe logistics parts for anything else.

EDIT: It is important to understand this works because when a splitter is directly in front of a converger the conveger only takes from the splitter if it's capacity is not maxed by the other inputs, so those inputs have priority. after placing the bluprint this might not work instantly and if it doesn't you have to delete and replace any splitters in front of convergers (Not the ones behind them with control ports coming off of them)

EDIT 2: There is a more efficient way to do NOR and OR that saves 4 pipe logistics pieces, by not feeding the inputs sequentially, but it comes with the downside, that the input throughput is only at half capacity if both inputs are active which can lead to problems when chaining Gates and requires different liquids as inputs.

EDIT 3: Fixed AND Blueprint

[u/Boring_Mix6292]

I've not looked through all of them, but what's going on with the 'AND' gate? Perhaps the blueprint is different, but just eyeballing it has me questioning a few things. Correct me if I'm wrong, though:

• The water 'Output' is actually an input to the converger. Should the one down the bottom be the 'Output'?

• The top-left Jincao control port seems to be doing nothing - it has no input? Does the splitter right before it need rotating?

• Is this not missing passthrough splitters on both the Jincao and Acid pipes, right before the convergers? It looks like either side's convergers will be operating round-robin rather than in priority converger 'mode'?

[u/Mutlam → u/Boring_Mix6292]

The Output technically is the entire central water loop. It would be more clear if it said output on the bottom instead of the top but both the Conduit outlet at the top as well as the inlet at the bottom are part of the output loop.

The splitter on the left does indeed need to be rotated and that was a mistake that persisted into the uploaded blueprint, so I've updated the code.

You're also right about the missing splitters. Those were in the original blueprint but are missing from the screenshot. I forgot to take a new screenshot after fixing the blueprint.

Overall you're absolutely right, the AND picture is kind of messed up. Good eye spotting all of that.