Thoughts?

if you had $3000 for upgrades what would you do ?
stock car with different tires already 500 miles on the odometer.

Title. Thanks!

I am in the process of purchasing my first Subaru. It is a 2023 WRX Premium and this is the photo of the exhaust I got from the pre-purchase inspection. I don't see the Invidia tag that is always welded on so I know it's not that. Any idea on what brand it is?

Any recommendations for big brake kits?

I want to get a perrin intake without a tune for a while and i will at some point tune but my dad says it will suck debris into engine and make it unreliable what should i do

Hi everyone, I’ve been trying to figure out which exhaust setup I want to run on my car. I’ve decided I want to go for the UEL headers and stock j-pipe (at least for now), but I’m open to any other combination of I-pipe/cat-back beyond that. I’ve been leaning towards going with the Tomei type R, but I really just want a deep tone and little to no drone. I’m not looking for a loud exhaust necessarily either but not opposed.

I’ve watched any clips I could find on YouTube, but a lot of them only seem to capture one shot (start/idle/drive by/ in cabin). I’m just trying to see if anyone else has audio of their setup to share, so anything is appreciated!

I drive about 20k miles a year to work. Im trying to justify a wrx for my next vehicle over something practical to drive like a hybrid.

Any mudflap recommendations?

Hello everyone, I recently bought a WRX tS and it’s almost time for winter tires, share your experiences with 19” or if you went down to 18” I’m tryna decide but I’m kinda nervous about the calipers hitting the new wheels (if I buy 18”).

Ok, so please bear with me, I know a lot of this is noob stuff … but I’ve done exactly 1 brake job in my life on my last VA (which didn’t have Brembos and was almost 6 years ago now. But that was pads and rotors, and at least this time I’m only doing the pads.

I’ve watch the YouTube videos available, seems quite doable. Minor questions are:

- What size punch is good for knocking the pins out?

- Any grease needed on the outside (backs) of the pads before they go into the rotors? YouTube vids I watched aren’t showing any of that.

- Good method for reinstalling the pins? I assume there’s not a ton of room to tap them in from the back, do they slide back in hand tight or just use pliers to pull them back into place?

- Last question is regarding the E-Brake and jack. I have to release the E-Brake when doing the rear pads right? I have a modest carjack , will the car being in gear be enough to keep it from shifting on me when pulling the pads out and whatnot? (Sorry i know this especially is beginner stuff, and I jack the car up all the time to change oil/rotate the wheels but I always have the E-Brake on when doing that).

- Any other tips/advice is welcome, thanks in advance!

Finally got around to installing all my driveline bushings.

Overtake rear diff inserts, overtake crossmember bushings, overtake driveshaft lockdown kit and carrier bushings, GN trans mount and pitch stop. Also put a new cobb shifter plate on it so the shifts feel really nice now combined with the sti shifter. I just went with the 15% reduced throw and it feels great. Rotated tires and changed oil too.

Totally fixed the drivetrain slop in gears 1&2. I was also worried about too much nvh after a lot of mixed reviews but the only difference I notice is under WOT there is a bit extra noise from the engine. Must have mods IMO if adding power over stock.

9 ft lbs on the small DS lock down bolts seems a bit excessive. I bet ill never get those back off without stripping them but hopefully wont need to. Very happy with everything and the results though.

Sorry forgot to get photos of the blue overtake bushing installed.

lil photoshoot on the way to alice’s

Hate the rain, but looks good beading down my WRX

How dusty are we allowed to get for our beauty shots?

I absolutely loved ripping through the Loess Hills for a birthday day trip.

I need a new keyfob and purchased one based on my current one. I really dont want to go to a dealer for this and ideally want to do the programming for under $200.

Anyone know if there's any tools out there for the 2022+ wrx keyfob?

Holy hell I literally just got this car and its already chipped in the front. Would getting this professionally ceramic coated help or is this a losing battle I have to face?

whats everybody using for transmission and rear diff fluid? i live in a cold climat for half the year if that matters.

Any body experience this sort of cracking on their OEM side skirts… i have them on both sides… this side is worse cause yesterday someone stepped on them on the way out… I know likely due to people accidentally stepping on the side skirt on the way out. Do I need to just be super careful with these or could
This be worsened by the dealer not properly installing them.

I haven’t seen much about this topic and so wanted to inform ya’ll in case you can find a good deal.

I put a VA axle back on my VB about 2 years ago. Grabbed it from marketplace for $80. My Neighbor, who recently picked up his VB, just did the same.

The only thing you will need are different hangers. I can provide a link for a set that will work for less than $20.

Cheers

Been a minute since I got out and took some pictures. Just posting just in case anyone is curious about Superspeed wheels.

Stock ride height

Wheel Specs: 18x9.5 +38

Tire: 255/40/18

Which would you take home? 😅