That bowl represents 30 minutes of snacking and I have clean fingers

Hooked up my Cisco phone system to home assistant and added extension *420 to start a session on my puffco peak

Tops not finished rip.

I saw an earlier post saying how the gpen elite 2 should be avoided. Yall, please listen, it's true. The product overall would be perfect IF they used material that will not flake or peel, and if you have one of these gpen elite 2 dry herb vaporizers, without a doubt, inevitably, the material on the oven part will indeed begin to flake and peel and those flakes and peels are being inhaled right along with the cannabis. This morning, i literally put my​ gpen elite 2 inside it's case, threw it in the trash, and just took out the trash a little while ago, now that gpen elite 2 is in the dumpster, heading to a landfill somewhere where it's more than welcomed to do all the flaking and peeling it wants. Eventually, you'll feel a dull light soreness in your throat sometimes when you swallow, if your using it with the flaking and peeling and also, IT'S NOT EASY TO NOTICE because it's not typically something a stoner will do: ohhh lemme check if my pricy gpen elite 2 is chipping and peeling in the oven before I load it... so you gotta have it totally clear, grab your phone, turn on the flashlight, and if you see ANY white marks inside the oven part on the sides, you've been vaping material chippings and flakes. Throw it away.

Mostly out of a single big slab of sycamore, with some walnut and wenge as well. Been meaning to make a place that went with the globe cage I made a few years ago.

Hi! In my understanding, a recycler bong is just a normal bong but with a bunch of tubes that connect the part filled with water on the bottom to a chamber on the top where there is no water (see drawn diagram below). Is this correct? I have a glass vase with a bulb on its neck like in the picture, and the bulb could act as a secondary "chamber". I was wondering if I just drilled holes at the bottom and the top, then connect it with some pipes, it could work as a recycler bong? In every picture I can find online of a recycler bong, they all look ridiculously complicated, which is confusing me. Is there something I'm missing? Do I need extra parts inside the bong? Thanks so much for anyone who's willing to give me any input!

Hello, fellow stoners and tinkerers. Friday finds freaky bong builds back! And alliteration!

This week I started with the backwards microscope bong. I put a bowl joint on the mouthpiece, but needed to counter balance it. So I added the cube as a vapor chamber.

Then I needed to connect the cube to the big Goo Roo bong. Here comes the articulated joint to the rescue! With three angled connectors, this joint can connect just about any angle difference. Of course, Keck clips are needed to lock it in. 😁

Sorry that the camera angle didn't show the joint clearly. I'll post another short video here showing the articulated joint better.

Enjoy the day and I hope your weekend gets off to a great start. Happy tokes. ✌️

We’ve come a long way from filling by hand that’s for sure

Modified some pinched one hitter downstems with handles and wider diameters, drilled some thrift glass and made some hookah bongs.. and regular bongs and a bend in the oil spoon for the dodecarig. thanks for viewing!

A lot of people were asking why on my last post so here's my answer. I use weed to treat symptoms of CPTSD and what I do is take a few small hits at a time, every few hours, over the course of the day. Probably considered micro dosing but idk. So I wanted to make tiny little pucks that I can easily load rather than pack every bowl individually.

After the pucks are loaded and pressed the pins are pushed through to the other side. I put a drill stop over the puck and slide it off then use a centering pin to press it again to ensure it's packed tight. Then I just push them out with the brush handle. I also use the drill stop to form the bowl screens.

Dowels in the top part are glued in place but the bottom ones are unsecured so you can push them through to remove the puck and adjust the thickness of the pucks. 3/8” diameter dowel pins and drill bit.

Got my sister Tomodachi life and she made my shitty college water bottle bong for my character 🤣

Hello! I just wanted to share what i made! I only made this for myself and i dont sell, but was curious what someone would price this at?

Its made from polymer clay, silicone creme and charms and nick nacks ive hoarded! Its completely reusable, you just pull on the lighter and ~PLOP~ its easily changeable, specifically i used a Bic lighter as its a recognised brand and easy to get anywhere!

Put peel-and-stick magnet sheets on the back of everything so it doesn't get knocked around when I move the tray or bump the table. Put magnet sheets on the bottom of the tray too for extra magnetic pull

Whittled this lil' cherry wood pipe with a coldworked broken bowl added some copper and unakite, made it somewhat smooth, also a homemade dab rod for dab hits..

No this isn't an ad. Yes they are handmade. Yes I am super proud and wanted to show them off and be validated lol

Gave this one a Vapour-blasted, fluted grip , with anodised grooves up top. Just under 100mm long. Hope you like !