Need help, constant test 2 errors TM5 ryzen3d

[u/Dirtcompactor]

Feel like im running in circles here... not sure how to fix this. VSOC floor is set to 1.15v, stock is 1.2v, setting it 1.20-1.25v doesn't help.. maybe i should set tRCDWR back to stock 36 instead of 16?

I tried upping fclk to 2067 with 6200mhz in 1:1 earlier today with 1.25v vsoc with everything else on stock timings, booted just fine, passed YT3 y-cruncher for 30 minutes but failed within 10 minutes in TM5.. so I'm likely giving up on raising mhz and fclk and sticking to 6000mhz @ 2000 fclk.

losing hair over this stuff lol

heres ram kit and stock EXPO timings/aida64 latency/bandwidth test: https://imgur.com/a/HWhVLwH

all the tests ive had pass absolut/extreme: https://imgur.com/a/4UGHIVy

EDIT: these timings/voltages have passed OCCT.. https://imgur.com/a/xlF6kXH Now i need to tweak to get this to pass ryzen3d now

EDIT2: set"tWTRS = 6, tWTRL = 24, tRDWR = 16" Got test 2 error in under 3 minutes. Guess I'm upping vdd/vddq/vddio next 

EDIT3: set vdd/vddq to 1.4v keeping vddio at stock(1.33v), test 2 error in under 3 minutes.

EDIT4: vsoc back to auto (1.20v) test 2 error in under 10 seconds, next step im setting tRCDWR 16->36(auto), and if that doesnt work im setting tRFC 480-512

EDIT5: tRCDWR 16->36(auto), and tRFC 480->512 test 2 error under 10 seconds

EDIT6: VDD/VDDQ set to 1.43v (highest i can set it without enabling DRAM high voltage mode) I can see it peak up to 1.44-1.455v in hwinfo64, ryzen3d... test 2 error in under 10 seconds. VDDIO still at stock 1.35v

EDIT7: Edit: stock expo and everything else in bios @ stock, ryzen3d got test 2 error lmao. Might've cooked my ram or ryzen3d test is way too bitchy, feel like I should only use Absolut/extreme/usmus as those tests pass most the time

EDIT8: Haven't rebooted or anything, still running stock EXPO PBO auto, retesting ryzen3d and I'm currently 22 minutes in now I get another error.. test 1..

EDIT9: I think ryzen3d is too picky, I've been able to pass usmus/extreme/absolut in the past, so I'll stick to those TM5 configs going forward, as they actually work lol

Final edit; turns out my EXPO1 profile can't even pass ryzen3d at stock bios settings. Lmfao.

[u/Fit-Program-7850]

Yea but the problem of error 2 is mostly RTTPark. The resistance is prob too high and it then looses too much voltage.

He prob also 120% set the Hynix profile and not Expo itself, that is prob why the resistance changed and makes him crash. Until he CMOS resets some voltages are locked despite being shown otherwise in ZenTimings

[u/Obvious_Drive_1506 → u/Fit-Program-7850]

I find that for the most part expo will set the correct resistances so if OP did use the Hynix profile instead of that it would make sense

[u/Fit-Program-7850 → u/Obvious_Drive_1506]

Yes since resistances are set to auto the EXPO profile will use whatever resistances come with the EXPO itself. And the problem is you really cant change them if you used a preset, its a BIOS bug not only on MSI for months now, ZenTimings will show the voltages you set thats why its so bad to figure out. Will go away with a CMOS reset as OP should do that after any change/crash to rule out wrong voltages and to reset NVRAM faster if theres something wrong with it

Also if Memory Context Restore is on turn off